Boat’n Bros RC Fisher Guy Assemblage – RC BOAT – RCTutos #231

Boat’n Bros RC Fisher Guy Assemblage – RC BOAT – RCTutos #231


Hello everyone
Welcome on RCTutos.fr Today we are back for the assembly of the Fisher Guy from Boat’n Bros RC So we have the same box that in the first video with different 3d printed parts and some parts like motor, motor mount, axle, bollard propeller and screws So let’s start the build together So first you need the 2 parts for floor and the 2 parts for deck you need a 2 compound resin glue and something to mix the glue so let’s prepare some resin glue, you don’t need a lot and you can glue the parts first we used a cooking paper sheet to use the flat support and the low grip of the paper when the glue will be hard let’s glue now the deck and you can join the 2 parts you can now hold 5 minuts we choose some 5 minuts hardening resin so you hold 5 minuts the other part there, is flat so no need to hold it but this one moves a bit so we need to hold the 2 parts are glued, we can now save them to let it hard well let’s grab the 2 parts for the hull and we will put some glue on all the contact surface So you prepare some glue you need a bit more this time no need to mix too much glue, we dont use a lot and you mix and you apply glue on all surface let’s put now the half hull on the other you align the 2 parts now the hull is glued, we can install the floor on the hull you will apply resin on all the flat base of the hull before installing the floor so you prepare some glue you put a good ammount, as the resin will make the waterproofing of the floor you can now put the floor you clean the excess of glue now let’s harden the glue now we can grab the deck and install the hood so let’s prepare some glue you need some clamps to hold it you prepare some glue and you apply some glue on the hood the round side upper, flat side on contact qith the deck you align the hood on the deck and block the clamps so let’s harden the glue let’s grab the rudder these 2 parts fits like that you prepare some glue and you put some on this side like that you make it fit and you let it harden next we prepare the lexan windows , we cut them on good size to make them fit with cabin dont forget to peel off the protective film on both sides and we will use cyano glue you glue all around the window and you install windows be aware of a good contact of the window around the hole we let this dry next we need the cabin roof and while windows dry, we prepare some glue next we will glue cabin here cabin aligns with the V of the hood let’s put some glue on the V and put some glue around here on the cabin you can now make them fit and you let the glue harden now we can glue the roof of the cabin you put some glue around the top of cabin you can now place the roof you can switch steps so first glue the roof before gluing the cabin on the deck so you can mark the centers to put it well aligned the advantage with the resin, is that we have time to make it fit well and center the roof it’s good so we can let it harden now you grab motor and motor mount and the 2 screws for motor we will install motor on motor mount motor mount goes on the front part of the hull on the flat zone, but you need to mount the motor first on the mount you need to glue it like that at the limit of junction so you can mount the motor let’s prepare the 2 supports for the hull you grab the 4 bases you can prepare some glue and put some on the contact zone and you can install the motor on the front of the hull at the junction and you hold while it harden so now you can grab the axle, coupler and allen key on the coupler you have 2 holes, the small goes on the motor big goes on axle you can put the axle in the tube and install the coupler first on axle and you can tighten the screw on the axle part like that next you put the coupler on motor axle and you can tighten be aware the center axle is full inserted you pres on the axle before tightening next step will be to resin al around the axle here and all around here we suggest you to fill the axle with marin grease to avoid water to go in the hull so we will prepare resin and make a joint here, let it dry and do the same on the other side let’s prepare some glue and you apply resin around the axle to make it waterproof now let it dry now we reverse the boat and do the same on the other side like that while the axle harden, you probably have a bit of glue remaining, we will use it to glue the rudder support you center it and put it at the level of the floor (dont look at the video there is a mistake) you just need a drop of glue the advantage is you don tneed to wait as the resin is already activated you center the part and align with the floor, not like shown in video and you hold it till it’s glued now we can install the propeller so you unscrew the bolt you grab the propeller, ther is a direction this part goes on the coupler and you can tighten the props is free to turn so let’s grab the long screw you need a flat screwdriver and we install the rudder like that, the rudder is free to move the propeller is free to turn motor is installed now let’s install the servo on the servo mount you put the servo like that you put 2 screws on the servo i suggest you to use allen screws if you need to unmount servo when support will be glued before gluing the servo mount, put the servo on neutral connect it to the receiver and put the transmitter trims on neutral after that you can install the rudder vertically if needed you can cut it to make it fit with the deck of the boat now you have cut the rudder, you can glue the servo mount it’s easy, the square in the hull fits with the square of the mount like that you prepare some glue and install the servo mount on the hull servo saver comes on the left of the boat you hold while it glues let’s make now the steering at 1cm you can flex the spindle at 90° you put it in the hole of the hull like that and you install it in the rudder servo is centered we align ethe rudder and mark where we need to flex the spindle you need a pen and you make a mark the place you need to flex to go inside the rudder you can take off at the servo but you let the spindle in the hull you can now flex 90° next you put the spindle in the rudder you can cut if needed next you install in the servo saver like that, the steering works the boat is now finished you can now go to the finishing steps you need to varnish the hull or with marine varnish or with resin and you can make a silicon joint around the hull and the floor to waterproof it if you do this, and grease inside the tube the boat will be waterproof so it was the build of the Fisher Guy from Boat’n Bros RC with the cyano, it makes the windows white if you can use another plastic glue or resin and hold thel with clamps it will avoid the white windows so for informations you can contact us on Facebook page Boat’n Bros RC Boats good assembly for them that build feel free to publish pics and videos of your builds feel free to customize them and share pics it was the Fisher 14″ from Boat’n Bros RC Boats thanks for watching subscribe for more videos like us on Facebook visit our website www.rctutos.fr you can also find us on instagram @RCTutos.fr This tutorial is brought to you in collaboration with our partners ATees, Banggood and Dagoma Thanks again
See you later

3 thoughts on “Boat’n Bros RC Fisher Guy Assemblage – RC BOAT – RCTutos #231

  • November 27, 2017 at 5:11 pm
    Permalink

    Superbe vidéo bien expliquer continue comme sa.

    Reply
  • December 4, 2017 at 10:23 pm
    Permalink

    Salut crisse ser flam62

    Reply
  • December 10, 2017 at 8:55 pm
    Permalink

    Ces quoi le truc orange avec les pneu dessus stp le nom

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *